The Gloster is at the stage of the " fiddly " bits.
I've decided to do the float attachment in brass rod with bass wood/balsa fairings. Bit of holding the tongue at the right
whilst positioning for shot. I'll make up a simple jig when its time to get serious. Psychological boost for me. The pencil
lines are for my benefit ( where extra work is needed).
Great subject Boomerang,well worth the extra effort needed with the float geometry.
Barry.
Coming along nicely.
Lou
Nearly but not quite finished.
Pictures below show floats ready for attachment and attached. Struts are brass tube faired with basswood.
Windscreen is a bit of recycled clear plastic which fitted on first try at folding. ( Got to be happy with that).
The tread over the wings is pre placed rigging. Was permitted into the imperial sowing kit and "borrowed" an appropriately
sized needle which I managed to thread twice on the first attempt ( two wins).
Proceeding along with the fairing of the struts to the fuselage. I use a "polyfilla "product which has a mirror finish
Finishes off brilliantly and when its dried I just use a damp cotton bud or a finger to get the desired affect.
The radiators are thin corrugated aluminium that I got from a hobby shop. Used "Supa" glue once desired profile was
achieved. Radiators everywhere. The info that I can find says they were "copper" coloured. Used a base coat of Acrylic
Gold with a thin wash of red over the top.
Powder blue fuselage, Bronze flying surfaces and engine covers. The "1"is from White decal paper. Its a wee bit
transparent but I managed get both on at the first attempt .... so no going back there. I might try hitting the paper with a
coat of white in future a see if that works.
Rigging to be done. Oil cooler will be added when all the struts and rigging work is complete.
Cheers
Gordon
Awesome job Gordon. The finish is great. What did you use to seal the floats. The metallic finish is perfect.
Lou
Thanks Lou,
I used Tamiya Aircraft Color "Bare Metal Silver"AS-12 from a "rattlecan" .
The Blue is "Model Color"- Sky Blue- Acrylic.
Cheers
Gordon
Thank you Gordon. I have not tried the Tamiya silver. I usually use Model Master buff-able metallics.
Lou
Might have a look at the metallics down the track. Theres a couple of coats of primer and a couple of coats of silver
cut back between coats on the floats
Saw the Tamiya AS-12 this morning. Unfortunately it is very pricey here and will have to wait until my allowance builds up a bit. I still have lots of spray stock on hand. Full can of Stainless Steel (2), Aluminum Plate (2 & 1/2) and Titanium (3). The shop where I go does not stock the stuff and my minimum order was 3 each at $6.00 CDN.
Regardless, I will keep Tamiya in mind when I use up the other stuff.
Lou
Gordon it really is a nice job. I'm not familiar with the aircraft but I guess that we can expect you to inform the Group of the aircraft's importance at a later date.
Cliff.
Cliff
An abridged history
The three Gloster IVs were first flown in July–August 1927, with the two short-span aircraft (the Gloster IVA and IVB) being
shipped to Venice in August 1927. The Gloster IVB was finally chosen to compete with the two S.5s in the race, the Crusader
having crashed due to having its control cables crossed on re-assembly.On the day of the race, 26 September 1927, the
Gloster IVB, piloted by Flight Lieutenant Samuel Kinkead was the first aircraft to take off, completing five laps before retiring,
with the race being won by Flight Lieutenant Sidney Webster flying the S.5.[6] On inspection, it was found that the Gloster's
propeller shaft was seriously cracked and would probably have failed if Kinkead had not retired.Following the race, the
Gloster IVA and IVB were returned to the United Kingdom, were they were modified to improve the pilot's view by raising the
upper wing and used as high speed trainers. They were used to train pilots for the 1929 race, with the IVB crashing during a
landing accident in December 1930 and the IVA used again as a trainer for the 1931 race. The original Gloster IV was
meanwhile sold with the intention of being converted to a landplane and used in attempt on the world air speed record but
these plans came to nothing.
Gloster IV
Serial number N224. Original larger wings. Powered by 900 hp (671 kW) direct-drive Napier Lion VIIA.
Gloster IVA
Serial number N222. Reduced span wings and modified tail. Powered by direct-drive Lion VIIA
Gloster IVB
Serial number N223. Reduced span wings and powered by geared Napier Lion VIIB engine
If you follow the link below it will take you to NACA Aircraft circular (69) which goes into some detail.
Of interest is the photos taken at the time of N223. Note no rudder stripes ,the numeral 1 and the serial applied in small
letters on the rudder only.
There is something written below this ( possibly Glocestershire Aviation Company) but I cannot make it out clearly so I'll just
leave that off.
http://digital.library.unt.edu/ark:/67531/metadc65060/m1/1/
Rigging has been completed with small patches of tape holding things in position negating the need to grow another
opposable thumb. Used cotton thread run through some primer and then some silver. Oil cooler added . Just some cleaning
up to do , apply the serial to the rudder and that will be it.
Picures to follow
Thanks Gordon, for the very interesting history of the Glosters and the racing. It requires a bit of digestion which I intend to do at a later date.
Cliff.
All finished.
Now in my son's display case.
On with the Beaufort.
( Maybe a Short Crusader a little bit further down the track)
Cheers
Gordon
Very nicely done.
Peter
Congratulations on a very attractive model. I am sure your son is very pleased with the results.
Lou
Thank You Peter/ Lou
He's going to knock up a beaching trolley when he gets the time.
Lou, I'm sure it's in the "How to" instructions somewhere.. but How do you edit the title of a post
in this case to add ..... Completed .
Cheers
Gordon
Select the first post in the thread and select modify. Change the title as needed and press save.
Lou
Thanks Lou,
Done
Cheers
Gordon